Diamond Drill MIAA-15 Bedienungsanleitung

OPERATIONS MANUALMODEL :CORE DRILLSAFETYTo Maintain the operation safety,make sure read and understand this instruction book BEFOREoperating this equi

DESCRIPTIONRACKSWITCH WITHCIRCUIT PROTECTORFEEDHANDLEBASELEVELING BOLTPOLEMOTORCONTROLLABLECLUTCHWATER COCKLED Electric CurrentIndicator9

EXPLODED VIEW10GEAR CASE & MOTOR SET24636223646137987155.14832337026426434039383536343029282725655352511132457116151420131210171819212250494746454

EXPLODED VIEW11FEEDING HOUSE 859295939486748987889091788384828177728076797573

EXPLODED VIEW12POLE BASE11211111011611811711511911311410310810410610097991091051071021019896

SPARE PARTS LISTGEAR CASE SETGear CaseMain ShaftWater Supply CoverWater CockO-ring 49x2O-ring 49x2Seal 28x42x8Bearing 6005LLUBearing 6005ZZSnap Ring R

GEAR CASE SETThird GearCooper WasherMetal BushingThird GearPlateFriction PlateDisk SpringDisk SpringMetal CollarFine U-NutBearing 6200ZZDiaphragmPlug

MOTOR SETBaffleBearing 6201LLUArmatureBearing 6200ZZFilling Ring 6200O-RingFieldField Screw M5x85Spring Washer M5Washer M5Motor HouseBrush TubeScrew M

FEEDING HOUSE SETFeeding HouseBearing 6003ZZSnap Ring R-35Feed ShaftFeeding HeadScrew M8x25KnobSpringFeeding HandleKnob Bolt 5/16x1-1/4SpringScrew M6x

POLE BASE SETPole CoverPoleRackScrew M6x55Spring Washer M12Screw M12x75Screw M12x65Screw M12x100Nut M12SpringWater Collector Fixed PlateSpringScrew M1

NOTES TO USERSCHECK THE FOLLOWING BEFORE STARTING OPERATION.18

SAFETY1NOTE: Since this is general instruction for safety, some of them may not be applicable to some of your machines.

OPERATING INSTRUCTIONSA. Machine InstallationDRILLINGPOSITIONAPPROX.200mmANCHORBOLT W1/2" * 120mmSQUARE WASHER 1/2"HEX. NUT W1/2"BASE

B. Cutter Attachment & Water SupplyWATER COLLECTORRETAINING FITTING

C. Start DrillingNOTE: DIAMOND BIT can perform drilling with light force. Do not apply excessive force. Too much force reduces m

NOTE: While current are not achieve indicate current of this machine but clutchidling, means DIAMOND BIT idling but motor still operating, then you ha

POLE FIXING SCREWBASE FIXING SCREWNOTE: Cores often drop from DRILL BIT at the completion of the hole. Use extreme care in operation at high places.

TROUBLESHOOTING24

MAINTENANCE & INSPECTIONCAUTIONBe sure to turn SWITCH off andunplug the machine beforemaintenance and inspection.NOTE:Dust or dirt inside MOTOR i

MAINTENANCE & INSPECTIONREPAIRS26

ANOTHER INSTRUCTION27

Intentionally Blank

2

Intentionally Blank

Intentionally Blank

DIAMONDPRODUCTS333 Prospect Street • Elyria, OHIO 44035 • USAPlease call us if for any reason you are having difficulty that cannot be resolved with t

3

4

USE OF CORE DRILL5

6

STANDARD ACCESSORIESAPPLICATION7

SPECIFICATIONSModelSpecVOLTAGEDEMANDIDLING SPEEDTWO-SPEEDAPPLICABLEBIT DIAMETEREFFECTIVESTROKEHEIGHTWEIGHT8MIAA-15110V (60Hz)2400W850 rpmNO1”-6”20”30”